Bosch dishwashers are very popular in households. They are very efficient and durable. They are fully integrated built-in dishwasher or free standing. It will take about 2 to 3 hours to install a Bosch dishwasher in your kitchen.

Manufacturers Free Installation Dishwasher Cleaner
Manufacturers Free Installation Dishwasher Parts
Manufacturers Free Installation Dishwasher Service
Manufacturers Free Installation Dishwasher Installation
Manufacturers Free Installation Dishwasher

Sometimes you may want to work it out by yourself to save the cost of installation. Other times it might not be easy so you might need to leave the installation to professionals.

The dishwashers are free with qualified purchases of Thermador cooking products. However, these free products are basic Bosch dishwashers. That said, the Thermador Star Sapphire is a pretty amazing dishwasher if it ever becomes available. To learn about Thermador's best dishwasher model, watch the video below. Between dishwasher and adjacent cabinet, wall or other appliances. Allow 25-5/8' min. Clearance from the front of the dishwasher for door opening. Figure B Note: ADA installation, (32-1/2”) beneath 34” high counter-tops may be accomplished by adjusting the toekick and leveling legs. Figure B DRAIN REQUIREMENTS † Follow local codes.

If you are planning to install your new dishwasher then you should check out these DIY tips below and ensure you install it the right way.

Bosch Dishwashers manufacturers usually include some of the installation materials needed to complete this process. You will have to buy other materials you will need. We hope that by the end of this article, you will know how to install a Bosch dishwasher.

If you prefer learning by video, this article is also explained here.

Video: Bosch Dishwasher Installation

Watch this video for everything you need to know about the Bosch dishwasher installation.

How to Install a Bosch Dishwasher – DIY Methods

Follow these steps to install your Bosch dishwasher yourself:

Shut Off the Power and Water Supply
Slide-in Your Dishwasher
Do the Drain Hose or Pipe Adjustment
Find the Junction Box
Connect the Water Supply to The Inlet Valve
Run A Dishwashing Cycle

Method A

Step One – Shut Off the Power and Water Supply

When you get your new appliance, the first thing to do is to shut off the power supply and the water supply under your kitchen sink to the dishwasher. This is very important as failure to do either one of the above-mentioned steps could cause a messy situation.

After doing this simple part, disconnect the access board below the Bosch dishwasher and set it aside. Be careful here, this part could be sharp.

Step Two – Slide in Your Dishwasher

You must make sure that the drainpipe is dragged in through your cabinet wall before you push in your brand-new dishwasher. After doing this, delicately move the appliance underneath the counter exactly the space it will fit in smoothly.

If the dishwasher is very short you can balance the legs easily below the appliance so that they will be on the same level. Then jam them into position with screws. Also, you will want to bolt the brace in that is on top of the appliance to the countertop. This is to ensure that it does not falter.

Step Three – Do the Drain Hose or Pipe Adjustment

Get hold of the drainpipe you previously slip in between the cabinet. Then drag the entire length through. Then you will attach the drainpipe to the garbage disposal or sink drainage using a clamp. Make sure that the pipe is high up than where it is connected so that there will be no drainage issue later.

Using a cable tie, tie up the pipe to anything above this connection. This is to ensure that there will not be an issue in the future.

Step Four – Find the Junction Box

It is located below the access board. Remove its cover to reveal the three screws: silver, green and gold. Loose each of these screws a little to enable you to connect the different cables to their corresponding slots.

Different dishwasher models may have a slight difference here, so it is imperative that you thoroughly read the product manual to understand this part.

Step Five – Connect the Water Supply to The Inlet Valve

Since the access board is off, the inlet valve can be seen easily now. You are going to attach it to your home water supply. It is also possible that there is still water inside the drain when the product manufacturers tested the appliance. As a result of this water might gush out from the drain.

Place the bottom access board back onto the dishwasher. The water and power are now ready to be turned on.

Step Six – Run A Dishwashing Cycle

Turn on the dishwasher and run a full cycle without any detergent or dishes. Check for any sign of leakages on the water supply hose and the drain pipe. Insert the toe-kick cover on the front of the appliance.

Check out these interesting articlesfrom our previous posts:

Method B

Step One

Loosen the strain relief plate so that you can have access to the electrical attachment on the appliance and attach the strain relief to it. Then put the power cable through this connection.

Fasten the clamp tightly around the cable wires but care must be taken not to tighten the clamp too much. Fix this entire connection into the junction box. Then fasten it with a screw.

Step Two

Detach 2-3” of the sheath at the cable wire end. Clear 1.5” of the sheaths from each wire. Put the green wire or naked copper in the opening that is marked ‘G’ and secures the screw.

Put the white wire in the opening ‘N’ and secure the screw. Put the black wire in the opening ‘L’ and secure the screw and return the junction box to its position.

Note that all screws must not be over-tightened.

Step Three

Connect the drain pipe using to drain connection at the back of the appliance a screwdriver brace. Fasten the other end of the pipe to the drainage pipe underneath your sink using a brace.

Ensure that the pipe is securely fastened before attaching with the brace.

Step Four

Delicately place your dishwasher on its back. Envelop the small brass bend with a Teflon tape and fasten it to the water supply line on the appliance particularly positioned at the back of the toe-kick sheath.

Connect your hot water line to the other brass bend end. Place the line in the passage under the system so that it runs out behind the appliance.

Carefully turn the dishwasher to its upright position and make sure the hot water line remains in the system. Turn on your hot water supply underneath your kitchen sink. Examine the line for any sign of leakage at both links.

Step Five

Turn the dishwasher under the countertop till its door is on the same level as front of the drawers and cabinet doors. Find the 4 leg adjustments in the front of the appliance.

Using a screwdriver, align the dishwasher from the back to the front. Turn it clockwise to lift the appliance and anti-clockwise to put it down. Repeat the same procedure to level it from one side to the other.

Step Six

Manufacturers Free Installation Dishwasher Cleaner

Move the attached mounting brackets positioned on top of the appliance far apart as much as they can go. Then use a screw and fasten tightly. Do the same with the other brackets.

Manufacturers Free Installation Dishwasher Parts

Step Seven

Turn on the dishwasher. Then run a full cycle without any detergent or dishes. Check for any sign of leakages on the water supply hose and the drain pipe. Insert the toe-kick sheath in the front of the appliance.

What Makes the Bosch Dishwashers Unique?

They are noise-free.
They are beautifully designed.
They have a large capacity.

They Are Noise-Free

This dishwasher company produces models that are noise-free. Their noise levels on the average are about 38dBA. This is due to how it wa